COVID-19 UPDATE - We are still operating so orders will be fulfilled as normal. Some lead times may be affected due to supplier closure but we are endeavouring to ensure minimal disruption to service.

LHQ24A100 - Linear actuator with rack 100 N, 3.5 s / 100 mm

On request
£129.33 £155.20

LHQ24A100 - Linear actuator with rack 100 N, 3.5 s/100 mm

•   AC / DC 24 V, Open/Close
•   Stroke range 0...100 mm, adjustable
•   IP 54, Manual override by means of push-button
•   Control single-wire 2)
•   Connection PVC cable 1m
•   Connection PVC cable 1m

More Information


  • Simple direct mounting The actuator can be directly connected with the application using the enclosed screws. The head of the gear rod is connected to the moving part of the ventilation application individually on the mounting side or with the Z-KS2 coupling piece provided.

  • Manual override Manual override with push-button possible (the gear is disengaged for as long as the button is pressed or remains locked).

  • Adjustable stroke The stroke of the gear rack can be adjusted on both sides in increments of 20 mm by means of mechanical end stops.
    A minimum permissible stroke of 40 mm must be allowed for.

  • High functional reliability The actuator is overload-proof, requires no limit switches and automatically stops when the end stop is reached.

  • Home position  The first time the supply voltage is switched on, i.e. during initial startup, the actuator carries out an adaptation. After pressing the «gear disengagement» pushbutton, the actuator moves to the home position at the end stop. The actuator then moves into the position defined by the control signal.

  • Adaption and synchronisation During adaptation, the upper and lower spindle end stop is recorded and deposited in the actuator. Detection of the mechanical end stops enables a gentle approach to the end positions and thus protects the actuator mechanism.
    During synchronisation, the actuator moves to the home position for referencing. This ensures correct position regulation.

Manuals & Datasheets
Technical Information

•     Electrical data Nominal voltage AC 24 V, 50/60 Hz / DC 24 V
•     Nominal voltage range AC 19.2 ... 28.8 V / DC 21.6 ... 28.8 V
•     Power consumption In operation 13 W @ nominal torque
•     At rest 2 W
•     For wire sizing 23 VA (I max. 20 A @ 5 ms)
•     Connection Cable 1 m, 3 x 0.75 mm2
•     Functional data Actuating force Min. 100 N @ nominal voltage 
•     Direction of stroke Reversible with switch 1 resp. 0
•     Manual override Gearing latch disengaged with pushbutton, can be locked
•     Stroke adjustment 20 ... 100 mm, adjustable in 20 mm-steps, can be limited at both ends with mechanical end stops
•     Stroke limiting Min. 40 mm
•     Running time 3.5 s / 100 mm 
•     Automatic adjustment of the operating range and the measuring signal U to match the mechanical stroke adjustment -Manual triggering of the adaption by pressing the «Adaption» button
•     Sound power level 52 dB (A)
•     Negative torque ! ≤50% from nominal torque (Caution: can only be used with restrictions. Please contact your Belimo representative.)
•     Safety Protection class III Safety extra-low voltage / UL Class 2 Supply
•     Degree of protection IP54 in any mounting position NEMA2, UL Enclosure Type 2
•     EMC CE according to 2004/108/EC
•     Certification Certified to IEC/EN 60730-1 and IEC/EN 60730-2-14 cULus according to UL 60730-1A and UL 60730-2-14 and CAN/CSA E60730-1:02
•     Mode of operation Type 1
•     Rated impulse voltage 0.8 kV
•     Control pollution degree 3
•     Ambient temperature –30 ... +40°C (no restrictions) +40 ... +50°C (Caution: can only be used with restrictions. Please contact your Belimo representative.)
•     Non-operating temperature –40 ... +80°C
•     Ambient humidity 95% r.h., non-condensating
•     Maintenance Maintenance-free
•     Dimensions / Weight Dimensions See «Dimensions» on page 5
•     Weight See «Overview of types» on page 1

Manufacturer Belimo